Pore Size: 0.22 µm: Inlet Connection: Sanitary Flange: Outlet Connection: Sanitary Flange: Air Diffusion at 23 °C: ≤13.3 mL/min @ 2.75 bar (40 psig) in water: Bubble Point at 23 °C: ≥3450 mbar (50 psig) air with water: Gravimetric Extractables
Field test results demonstrate this finding in a direct comparison of two microfiltration membranes with 0.2 µm nominal pore size made from either polyethersulfone (PES) based polymers or polypropylene (PP). When filtering the same white wine, the 3M™ Liqui-Flux™ Beverage Membrane Modules, using 3M’s unique PP hollow fiber membrane, revealed a much higher through put and service life compared to modules utilizing PES membranes.
pore size 0.2um ghp acrodisc maximum operating pressure 2.1 bar Aijiren Technology HPLC Part List | Official GiMiTEC™ Website 3 x 186003460 Acquity UPLC BEH HILIC 1.7祄 2.1 x 50m 3 x 716002254 Cert., 1-Day Service Informatics
Nanofiltration membranes have a nominal pore size of approximately 0.001 microns and an MWCO of 1,000 to 100,000 daltons. Pushing water through these smaller membrane pores requires a higher operation pressure than either MF or UF. Operating pressures are usually near 600 kPa (90psi) and can be as high as 1,000 kPa (150psi).
0.2 µm Minimum Bubble Point 3.4 bar Maximum Operating Temperature (Metric) 100 °C Unit of Measure PAC Min Order Qty 1 List Price $ 196.02 Add to Cart Add to Quote HPLC Mobile Phase Filtration Membranes - 0.2 µm, TF (PTFE) membrane (100/pkg) Product ID 66143 Removal Rating 0.2 µm Filter Media PTFE Minimum Bubble Point 1 bar
Whatman Nuclepore Polycarbonate Black Membrane Filter, 0.2 µm Pore Size, 25 mm Circle, 100 Pack, 110656. Regular Price $155.69 Price $135.38. Add to Cart. Whatman Nuclepore Hydrophilic Membrane, 0.2 µm Pore Size, 8 x 10 in sheet, 25 Pack, 10417050. Regular Price $833.64 Price $724.90.
Pall polyethersulfone membrane flow rate outperforms nylon and PVDF membranes of the same pore size (0.2 µm). Pall PES Membrane is Low in Biomolecule Binding. 125 I-labeled BSA (1.6 µg) or 32 P-labeled DNA (500 ng) was diluted to 5 mL in PBS (BSA) or Tris-EDTA (DNA) and filtered through a 13 mm disc of the indicated membrane. Filtration was
Maximum Operating Temperature: 55°C (131°F) Maximum Operating Pressure: 0.2 and 0.45µm is 6.9 bar (100psi) GF/0.45µm is 6.3 bar (90 psi) Typical Water Flow Rate (mL/min at 2.1 bar (30psi)) 0.2µm, 25mm is 60 0.45µm, 25mm is 65 0.45µm, 25mm GF is 60: Typical Water Flow Rate (mL/min at 0.7 bar (10psi)) 0.2µm, 13mm is 17 0.45µm, 13mm is 28
Hydrophilic polypropylene; Pore Size. 0.2 and 0.45 µm; Typical Thickness. 0.2 µm: 101 µm (4.0 mils) 0.45 µm: 114 µm (4.5 mils) Typical Water Flow RatemL/min/cm 2 at 0.7 bar (70 kPa, 10 psi) 0.2 µm: 20; 0.45 µm: 31; Maximum Operating Temperature. 55 °C (131 °F) Minimum Bubble Point - IPA. 0.2 µm: 1 bar (100 kPa, 14.5 psi) 0.45 µm: 0.
Hydrophilic polypropylene; Pore Size. 0.2 and 0.45 µm; Typical Thickness. 0.2 µm: 101 µm (4.0 mils) 0.45 µm: 114 µm (4.5 mils) Typical Water Flow RatemL/min/cm 2 at 0.7 bar (70 kPa, 10 psi) 0.2 µm: 20; 0.45 µm: 31; Maximum Operating Temperature. 55 °C (131 °F) Minimum Bubble Point - IPA. 0.2 µm: 1 bar (100 kPa, 14.5 psi) 0.45 µm: 0
Jan 7, 2023 · All-purpose, universal hydrophilic polypropylene membrane with maximum chemical compatibility when filtering both aqueous solutions and aggressive solvents. Low protein binding of GH Polypro membrane provides high recovery of critical proteinaceous samples. HPLC certified to assure that the filter will not add artifacts to your analysis.
Sterlitech PES (polyethersulfone) membrane filters, 0.2 micron pore size, 47 mm diameter, pack of 100. Hydrophilic, low protein/drug binding, minimal extractables, and broad chemical tolerance; ideal for pharmaceutical, medical, and life science applications. SKU PES0247100 Manufacturer Sterlitech Pore Size 0.20 Diameter (mm) 47 Pack Size 100
Absolute pore size ratings typically refer to the largest pore size of a membrane and it is expected that all pores will be equal to or smaller than the absolute rating. For the polycarbonate track-etch (PCTE) and polyester track-etch (PETE) membrane filters, porosity is the percent of the total surface area occupied by the pores; it typically
What membrane filter pore size should I use for sterilization? Regardless of the membrane filter material, always use a 0.2 µm pore size membrane filter as the final filter for any sterilizing filtration. The 0.2 µm membranes used in Aijiren Tech™ Nalgene™ filters have been tested and shown to retain 100% of a challenge of 1 X 107
Pore size: 0.2um. 1.20. $194.62. 66629. GH Polypro (GHP) Membrane Disc Filters Hydrophilic polypropylene membrane with maximum chemical compatibility when filtering both aqueous solutions and aggressive solvents. High recovery of critical proteinaceous samples due to low protein binding. HPLC certified. 13mm diameter. Pore size: 0.45um. 1.20